Christmas Inflatable Not Inflating? Fixes for Flat or Falling Figures

By the Urban Picks team · Updated

A Christmas inflatable that will not inflate almost always has one of four problems: no power at the fan, a zipper or opening at the base left open, a fan intake that is blocked or lying on the ground, or fabric that is pinched or twisted. Check them in that order and most figures stand up in a few minutes. This guide answers the questions people ask once the figure is in the yard: why it will not inflate, why the fan runs and the figure stays flat, why it deflates at night, how to find and patch a hole, why it leans or falls over, whether it can stay up in rain, snow or wind, and how to dry and store it after the season. The figures we carry run on an internal fan that must stay connected to power, so most fixes start at the outlet and the base. Ships to US addresses only.

Key takeaways

  • If a Christmas inflatable will not inflate, check in this order: power at the outlet (reset the GFCI), the plug and adapter connection, the zipper or opening at the base, and the fan intake.
  • A fan that runs while the figure stays flat points to an open base zipper, fabric folded over the intake, a pinched sleeve or a hole.
  • A figure that is flat in the morning was usually switched off by a timer or a tripped GFCI outlet; several of our figures are made to run no more than eight hours at a time.
  • Find a hole by feeling for air or brushing soapy water over the seams, and patch a small one with ripstop repair tape on clean, dry fabric.
  • Heavy rain, snow and strong wind are reasons to unplug the fan and take the figure in, and a dry fabric before folding keeps it from mildewing in storage.

Why won't my Christmas inflatable inflate?

Start with power: a Christmas inflatable stands only while its fan is connected and running, so an outlet that has no power is the first thing to rule out. Plug a lamp or a phone charger into the same outlet. Outdoors, the outlet is usually on a GFCI circuit, and a GFCI that has tripped cuts power without any sign on the figure. Press the RESET button on the outlet, or on the first GFCI outlet on that circuit, and try again.

Next, check every connection between the wall and the fan. Push the plug in all the way, and on figures with a separate adapter, check that the small round plug from the adapter is seated in the fan. Look along the cord for a cut or a crushed spot. Keep the plug connection off wet ground, for example inside a weatherproof cord cover.

Then look at the base. Many yard inflatables have a zipper or a closable opening at the base that lets you reach the fan and the stakes. If it is open, the air escapes as fast as the fan can push it in. Zip it shut or close it as the manual shows. Not every figure has one, so check the manual that comes in the box.

Last, lay the figure out flat with the fan intake clear before you power it. A fan whose intake is covered by folded fabric, leaves or snow cannot move air. The figures we carry include a manual, and the pages of the 12 ft snowman, the 6 ft train, the 10 ft castle and the 6 ft gingerbread man all say the fan has to stay connected to power for the figure to stay inflated.

Why is the fan running but the inflatable stays flat?

If you can hear the fan and the figure stays flat or only half stands, air is escaping or not reaching the body: the base zipper or opening is open, the fabric is folded over the intake, a sleeve or the fabric around the fan is pinched, or there is a hole or a split seam. Work through them in that order, with the figure unplugged between checks.

Check the opening first. Run your hand around the base for a zipper or closure that is not fully shut, and check the zipper pull is not caught in the fabric. Then look at where the fan meets the fabric: a twisted sleeve or a fold of fabric pressed against the intake will leave the figure flat while the fan hums.

Straighten the figure on the ground before you power it, front facing the street, with arms, hats and long pieces such as a train or a long neck laid out and not folded under the body. A figure that was stuffed into the box will take a few minutes to fill, so give it two or three minutes before you decide it is broken. If it stays flat after you have cleared the intake, closed the opening and straightened the fabric, look for a hole (see below).

A figure with more than one fan can fill unevenly if one fan is not running. The 10 ft castle has two internal fans, according to its page, so if only part of it fills, check that both are running.

Why does my inflatable deflate at night?

The usual reasons are a timer that switches the fan off, a tripped GFCI outlet, or a power cord pulled apart. When the fan stops, the figure settles onto the lawn. Check what turned the fan off before you look for a hole.

A timer is the most common cause, and on many of our figures it is also the right setup. The pages of the 12 ft snowman, the 6 ft train, the 11 ft dinosaur and the 10 ft gingerbread archway all say not to run the figure for more than eight hours at a time. An outdoor plug-in timer set to switch on at dusk and off at bedtime keeps within that, and the figure settling down at the end of the evening is how it is meant to work.

A GFCI outlet that trips in damp weather is the other usual cause. Moisture at the plug connection or in an extension cord can trip it, and the figure is flat in the morning. Reset the outlet and lift the connection off the ground, into a weatherproof cord cover. If it trips again on a dry night, stop using that outlet for the figure and have the circuit checked rather than working around the GFCI.

Check the shared circuit as well. Several figures plugged into one outlet add up their amps, and a breaker that trips at night takes them all down. Our guide https://urban-picks.com/guides/outdoor-christmas-inflatables-size-yard-lights-power lists the input ratings that the pages give, so you can add them up.

If none of that explains it, a small leak that the fan cannot keep up with will show as a figure that sags as the night goes on, and it needs the hole check below.

How do you find and patch a hole in an inflatable?

To find a hole, inflate the figure, then run your hand slowly over the fabric and seams and feel for air; where it is hard to feel, brush soapy water over a seam and look for bubbles. Mark the spot with a piece of tape or chalk, unplug the fan and let the figure deflate. These are general repair steps and do not come from any one product's page.

Clean and dry the fabric around the hole. For a small tear or a pinhole, apply a patch of ripstop nylon repair tape, the kind sold for tents and jackets, over the hole and press it flat, rounding the corners so they do not peel. A patch on the inside and a patch on the outside hold best, but the outside is usually all you can reach. Let it set as the tape's own instructions say before you inflate the figure again.

A split seam or a hole larger than your hand is a sewing or a replacement job, not a tape job. Stop inflating the figure so the split does not spread.

None of the contents lists on the pages we checked, the 12 ft snowman, the 6 ft train, the 10 ft castle and the 6 ft gingerbread man, includes a patch kit, so buy repair tape separately. If a figure arrives with a hole or does not work out of the box, our returns policy applies: 30-day returns on unused items, with return shipping on you unless the item arrived damaged, defective or wrong.

Why does my inflatable lean or fall over?

A figure leans or falls because wind pushes on its broad side like a sail while only a few stakes and tethers hold it down. Stake every base loop before you inflate, tie the tethers out at about 45 degrees, and put the figure where the house or a fence blocks the wind. A tall, shallow figure leans sooner than a squat one: the 8 ft gingerbread man is 94.5 in tall and only 25.5 in deep, so it needs every tether in the box.

A figure that leans while it fills usually has a stake that has pulled partway out or a base that was not laid flat. Unplug it, reset the stakes and fill it again instead of hauling it upright with a tether.

Our guide https://urban-picks.com/guides/how-to-secure-inflatable-yard-decorations covers stakes, tethers, sandbags and what to do on concrete or frozen ground.

Can it stay up in rain, snow or wind?

In light rain, an IP44 figure can stay up, but in heavy rain, snow or strong wind the makers say to take it down. IP44 covers splashing water from any direction, not a downpour, and the pages of the 6 ft train, the 10 ft castle, the 11 ft dinosaur and the 12 ft snowman all say not to use the figure in heavy rain, snow or wind.

Unplug the fan, let the figure deflate and bring it in or leave it staked down until the weather passes. Our guide https://urban-picks.com/guides/can-christmas-inflatables-stay-out-in-rain-and-snow has what each maker says about weather, figure by figure.

How do you dry and store an inflatable after the season?

Unplug the fan on a dry day, let the figure deflate, wipe the fan housing and plug with a dry cloth, and let the fabric dry completely before you fold it. A damp figure folded into a box is how mildew starts.

Fold it loosely, without hard creases along the printed or lit panels, coil the tethers, empty the sandbags, and keep the stakes, tethers and manual in the same box as the figure. The polyester bodies deflate for storage, so you do not keep a rigid display in the closet. Store the box somewhere dry, off a damp floor.

Next season, plug the fan in and inflate the figure on the lawn before you stake it down, so you find a hole or a bad connection on a clear day and not on the night of the party.

Fan, run limit and cord on eight of our inflatables

The table lists what each page says about the fan, the run limit and the cord, so you know what to check when a figure goes flat. Where a cell says none given, the page does not state a limit. All of these ship to US addresses only.

Questions

Why won't my Christmas inflatable inflate?
Check four things in order: power at the outlet (reset the GFCI), the plug and adapter connection, the zipper or opening at the base, and the fan intake. A fan that gets no power, an open base or an intake covered by fabric are the usual causes.
Why is the fan running but the inflatable stays flat?
Air is escaping or not reaching the body. Close the base zipper or opening, clear fabric from the fan intake, straighten any twisted sleeve, and give the figure two or three minutes to fill. If it stays flat, look for a hole or a split seam.
Why does my inflatable deflate at night?
Most often a timer switched the fan off or a GFCI outlet tripped in damp weather. Several of our figures, including the 12 ft snowman, the 6 ft train, the 11 ft dinosaur and the 10 ft archway, are made to run no more than eight hours at a time, so a dusk-to-bedtime timer is the right setup.
Why does my GFCI outlet keep tripping with an inflatable?
Moisture at the plug connection or in an extension cord is the usual cause outdoors. Lift the connection off the ground into a weatherproof cord cover and reset the outlet. If it trips again on a dry night, stop using that outlet and have the circuit checked instead of bypassing the GFCI.
How do you patch a hole in a Christmas inflatable?
Unplug it, find the hole by feeling for air or by brushing soapy water over the seams, clean and dry the spot, and press ripstop nylon repair tape over it with rounded corners. A split seam or a large tear needs sewing or replacement.
Can you leave a Christmas inflatable on all night?
Not the ones whose pages give an eight-hour limit: the 12 ft snowman, the 6 ft train, the 11 ft dinosaur and the 10 ft archway. Use an outdoor plug-in timer to switch the fan off at bedtime. Check the manual for any other figure.
Why does my inflatable lean or fall over?
Wind pushes on its broad side while a few stakes hold it. Stake every base loop, tie the tethers out at about 45 degrees and shelter the figure from the wind, and reset any stake that has pulled out. Ships to US addresses only.
How do I store an inflatable after Christmas?
Unplug the fan, let the figure deflate, let it dry completely, then fold it loosely with the stakes, tethers and manual in one box and keep it somewhere dry.

Related picks

More in Holiday & Seasonal →

Questions about a specific product? Email support@urban-picks.com or see the FAQ.